Goonhub
07-06-2021, 09:48 AM
Old Atmospherics in a nutshell was set up cans in proper configuration, sometimes put an empty can on the lines (For later) and cut your holes. Now if you maintain pipes for a short while and just barely babysit it, you could have a nice rip roaring hellburn. Am I missing much? Cutting all the fire alarms for easily moving around engineering, using the empty can to pull superheated gas and then putting it back into the hotloop feed to spike the output, stuff.
Now what do we have to do to get high temps? Right so..
Set up cans, burn chamber oxygen can needs to be spiked, so I need to drag the air filter into the router and start farting. I'm likely farting here till said engineers preferred kPa. I like 400 kPa. Now i've spent 5m farting like 300 times, I can now mix an o2 can with my fart filter and plop that on the engine. I'm also going to try for every mW I can get, so i'm going to put the filter on the hotloop too and tweak the kPa input on the valve to somewhat match the mix that the burn chamber has.
Then I need to cut all the hole in the floor like normal because it still burns itself down. Now I need to go to mechanics, I need to setup a teleporter system into the burn chamber so that I can warp molitz B into the chamber. But, if I warp molitz B in now, it would just float off into space. So I also need to build some dumbass containment unit. The only thing I can think of right now that is a blocker but also allows gas to flow over it? Air filters. So I fill the burn chamber with them but set them to off, and then I put a telepad in the middle.
Alright i've got my Molitz cage set, now I NEED Molitz. So let me go pray that mining gives a single fuck about anyone else on the entire station and go check that out, lets say by mercy, its there. Now I need to go to the clown hole and get helium, because I need Harm lube to lube up the turbines, then I need to either frozen fart if i'm lazy, but we apparently aren't here, I need to Electrum plate the engine core. Just doing that takes a good 10m. Now I need to hotwire the engine onto itself, because if this burn is actually successful, the engine will literally fucking kill itself because APC's don't charge fast enough. By the grace of god, if things keep going I need to babysit the burn chamber to always put Molitz in every 4m, make sure pipes don't burst, purge the engine every so often, etc etc etc. Its like i'm driving a locomotive and i'm going 5mph for all my work.
If my engine burn actually works, engineering is now superheated (Barely) and also the APC is hotwired and unsafe. After all that work i'd appreciate SOME power output, but its abysmal and terrible. No, I do not like the new atmospheric works.
If we had the ability to put molitz b into the gas extractor and fab a Molitz B can and then mix that with a gas and put it straight into the burn chamber i'd be just a tad bit happier. Maybe even putting frozen Farts into the fab could make a fart can too. More gases would be nice.
Now what do we have to do to get high temps? Right so..
Set up cans, burn chamber oxygen can needs to be spiked, so I need to drag the air filter into the router and start farting. I'm likely farting here till said engineers preferred kPa. I like 400 kPa. Now i've spent 5m farting like 300 times, I can now mix an o2 can with my fart filter and plop that on the engine. I'm also going to try for every mW I can get, so i'm going to put the filter on the hotloop too and tweak the kPa input on the valve to somewhat match the mix that the burn chamber has.
Then I need to cut all the hole in the floor like normal because it still burns itself down. Now I need to go to mechanics, I need to setup a teleporter system into the burn chamber so that I can warp molitz B into the chamber. But, if I warp molitz B in now, it would just float off into space. So I also need to build some dumbass containment unit. The only thing I can think of right now that is a blocker but also allows gas to flow over it? Air filters. So I fill the burn chamber with them but set them to off, and then I put a telepad in the middle.
Alright i've got my Molitz cage set, now I NEED Molitz. So let me go pray that mining gives a single fuck about anyone else on the entire station and go check that out, lets say by mercy, its there. Now I need to go to the clown hole and get helium, because I need Harm lube to lube up the turbines, then I need to either frozen fart if i'm lazy, but we apparently aren't here, I need to Electrum plate the engine core. Just doing that takes a good 10m. Now I need to hotwire the engine onto itself, because if this burn is actually successful, the engine will literally fucking kill itself because APC's don't charge fast enough. By the grace of god, if things keep going I need to babysit the burn chamber to always put Molitz in every 4m, make sure pipes don't burst, purge the engine every so often, etc etc etc. Its like i'm driving a locomotive and i'm going 5mph for all my work.
If my engine burn actually works, engineering is now superheated (Barely) and also the APC is hotwired and unsafe. After all that work i'd appreciate SOME power output, but its abysmal and terrible. No, I do not like the new atmospheric works.
If we had the ability to put molitz b into the gas extractor and fab a Molitz B can and then mix that with a gas and put it straight into the burn chamber i'd be just a tad bit happier. Maybe even putting frozen Farts into the fab could make a fart can too. More gases would be nice.